Sport & Old Timer
The Eugly Stick Spans 31” with a  Flying weight; 8 oz. Power; GWS IPS “A” Drive
w/ Medusa 5400 kv In-runner, Thunderbird 9 ESC w/ BEC, GWS 8-6 Prop, and a
Kokum 700 mah 3 cell Lipoly Battery. Guidance is 4 ch. R/C using 3 Sub-Micro
Servosand the Spektrum DX-6 radio.

Price: $32.95
The Comet Sparky Spans 55"   with a Flying Weight: 14.2 oz. Power: Suppo
2208-13 Outrunner with a 10A ESC w/ BEC, GWS 9-5 DD prop and a 2S, 1600
mah Lipoly battery. Guidanceis 2,  Sub-Micro Servos and a Spektrum AR6000 Rx.

Price; $59.95
The Quaker Flash Spans 55" with a Flying Weight- 13 oz. Power: 2208/17 (1100
KV) Brushless Outrunner  w/ a 10 amp ESC w/ BEC, a 9-4.7 Prop and a
Thunderpower 1320 mah 2S Lipoly Battery. Guidance is 3 ch. control is provided
by 2, Sub-Micro Servos with a Spektrum AR-6000 Rx.

Price $54.95   
The Comet Gull II spans 50"    with  Flying Weight: of 13 oz.  Power: TP 2208-17
Outrunner with a 20A ESC w/ BEC, GWS 9-5 DD prop and a 2S, 1600 mah Lipoly
battery. Guidance is 2,  Sub-Micro Servos and a Spektrum AR6000 Rx.

Price; $59.95
   
   
Free Flight
The Stinson Voyager is a 26" span model for Rubber Powered Free Flight.

Price: $21.95
The L-19 Bird Dog is a 26" span model for Rubber Powered Free Flight.

Price: $21.95
The Stinson L-5 Sentinal is a 26" span model for Rubber Powered Free Flight.

Price: $21.95
The B-737 is a 10" Span all balsa Sport Model for Catapult Launch. The Kit
contains the Launch Handle and Rubber Band.

Price: $9.95
The B-727 is a 10" Span all balsa Sport Model for Catapult Launch. The Kit
contains the Launch Handle and Rubber Band.

Price: $9.95
The Bell X-1 is a 10" Span all balsa Sport Model for Catapult Launch. The Kit
contains the Launch Handle and Rubber Band.

Price: $9.95
The F-84 Thunderjet is a 10" Span all balsa Sport Model for Catapult Launch.
The Kit contains the Launch Handle and Rubber Band.

Price: $9.95
The F9F Panther is a 10" Span all balsa Sport Model for Catapult Launch. The
Kit contains the Launch Handle and Rubber Band.

Price: $9.95
The V-1 Flying Bomb is a 10" Span all balsa Sport Model for Catapult Launch.
The Kit contains the Launch Handle and Rubber Band.

Price: $9.95
   
Page 1 2 3
Due to the widely varying of Postal Rates and package size limitations, outside
of U. S. orders must be calculated per order based on the size and weight of
the package and the country of destination. Drop a line at
patscustommodels@aol.com and we'll figure up the rates for your specific
order.
Floats
The 23" Float Kit is designed to fit the 1:8 scale Short Kit line. The Float Short
Kits include everything needed to build the floats, and patterns to fabricate the
brass water rudder assembly and general instructions to fabricate the strut
assembly for the models they'll be used on.
The floats, laser cut from Depron Foam, finish at about 1.8 oz. each, plus the strut
assembly, so will only add a couple of ounces to your finished model. Shown on
1:8 Scale Aeronaca Champ -- Airplane not included.

Price: $29.95
The 32" Float Kit is designed to fit the larger models in our Short Kit line. The
Float Short Kits include everything needed to build the floats, and patterns to
fabricate the brass water rudder assembly and general instructions to fabricate the
strut assembly for the models they'll be used on.
The floats, laser cut from Depron Foam, finish at about 2 oz. each, plus the strut
assembly, so will only add a couple of ounces to your finished model. Shown on
the 60" Pilatus Porter -- Airplane not included

Price: $32.95
Selecting the Proper Floats and Setting Up Your Model: To set up the floats on your specific
model, measure the fuselage length and multiply that by .7. Then select the kit closest to the required
length.
The floats are located on the model with the step on C. G. The wing saddle set to 1 degree positive
incidence with the top of the float at 0 degrees. The mounting struts should be set up so that the top of
the float is at the same height as the wheel axle on the main landing gear would have been. The water
rudder is mounted on the side that the entry door on the model the floats are to be mounted on is
located.